MSI Radeon HD 7750 DirectX 11 R7750-PMD2GD3 2GB 128-Bit DDR3 PCI Express 3. My question is, with the history of memory issues and the performance slide prior to this, is this likely a memory failure (no beeps or error code indicate this)? If so, why is the Boot Device LED on? Was there never an issue with the Mem and I've had a defective MB this whole time that has how progressed to be non operational?ĪSUS SABERTOOTH 990FX R2.0 AM3+ AMD 990FXĪMD FX-8350 Black Edition Vishera 8-Core 4.0 GHz (4.2 GHz Turbo) Socket AM3+ 125WĪDATA XPG V1.0 16GB (2 x 8GB) 240-Pin DDR3 SDRAM DDR3 1600Ĭrucial BX100 2.5" 250GB SATA III MLC Internal Solid State Drive (SSD) so I shut it down and the next day the boot device issue was there. The day before this started to happen my system began running very slowly (10-15 sec to open a folder, programs freezing). Now, after the MEMOK step, the Boot Device LED illuminates, and that's where it ends.ģ.Push the MEMOK button, MB resets, Boot device LED turns on, the end. This is required on all startups from no power, however restart would work with no mem issues. save mem settings, exit bios, successful boot. Once the system was running however there were no issues.Ģ.Cycles the LED indicators (CPU, Boot Device, Mem) after mem led it resets and all LEDs light up in that sequence infinitely.ģ.Push the MEMOK button, MB adjust mem settings, boots into BIOS.Ĥ. I built this computer a year ago with mostly new parts (reused power supply and GPU) and it has always been a bit finicky.įrom day one the MB has had an issue with the memory (correct type/timing for mb) that has forced me to use the MEMOK feature on boot to get a post. Dominator plats and gskill are the way to go.After a year of use I just started getting a red Boot Device LED on boot, and nothing happens after. Its been nothing but trouble for this board. If your ram is Vengeance series from corsair get rid of it. Final step is to take it to a shop for troubleshooting. Try different video cable and video inputs on monitor. Turn monitor power on and then hit the power button, give the mobo 5-7 minutes, you should notice gpu and cpu fans spinning up if not try a different psu. Ensure power cable is fully plugged into monitor and power strip/wall outlet, hook up and ensure psu power cable is hooked up fully to psu and in wall or powrr strip. ensure monitor cable is hooked up to your monitor fully and set to correct video input. Hook up the keyboard and mouse using the usb ports closest to the ps2 port. Ensure atx, eps 12v (at top of mobo towards rear) hooked to mobo, then pcie power is hooked up to gpu properly. clear the cmos using the jumper (read your manual), put jumper back in its spot, apply tim to the cpu and reattach heatsink to cpu mount bracket and fan to cpu header. Asus TUF 990FX Sabertooth R2 2901 Bios: Cooling: Scythe Ashura. Disconnect power totally, ensure ram is in slots 2 and 4 from left to right, ensure to shove gpu into pcie x16_1 fully seated, hook up a monitor closest to the screw side if the pci bracket. All done but the cpu debug led blinks red, if I remove the ram the missing ram led. Since the socket lays on 1 side and the latch bar is closer to the pcie socket, the tip of the latch bar faces left, ensure when you insert the cpu the letters are closer to the ram and not up and down on the mobo. Ensure mobo is placed on the box it came with ,psu,gpu, out of case completely, Take the heatsink off, take cpu out of socket, ensure you dont have any bent pins on the cpu.
0 Comments
Leave a Reply. |